- I recently purchased a set of Volvo's with no Transmissions.
They have the Ring Gear, but I need everything - back, Bell Housing etc.
Any information you could give me would help a lot as far as availability and costs.
Thank you.
Hello:
We can help you with this, but I would need a bit more information.
The AQD 40s came with a few different transmissions. The early ones ...
- I have a 2007 Rinker Express cruiser with a 20 pitch dual prop. Would I benefit going to a 22 or 24 pitch dual prop?
Hello:
That is tough to answer as it depends upon the boat, the horsepower, the ratio of the drive. We have on our blog and in ...
- IPS-C Conversion Kit Question
Hello :
Attached is a picture of the conversion kit for your IPS-C. This means that all the oil is cooled instead
of just the oil bypass ...
- Issue Replacing 2002 with a 120SC with 130 Saildrive Question Part I
Hello Mike:Below is the letter I wrote to the customer explaining what the issue is. The questions I have are:1) Is the companion flange 3581117 ...
- Issue with Replacing 2002 with 120SC with 130 Saildrive Question Part 2
Hello Mike:Below is the letter I wrote to the customer explaining what the issue is. The questions I have are:1) Is the companion flange 3581117 ...
- I have a ZF45A transmission on a yanmar 170hp 4lh-dte.
I would like to put a trolling valve on it because it idles too fast. It's very hard to handle at the slip.
Would the trolling valve permit me to shift gears at the dock at a slower speed? Thank you.
It sounds like your prop is probably too aggressive so you can't go slowly at low RPMs.
If you put on a smaller prop you may ...
- Is there a tool to remove impeller number 21700445?
Hello:
As you are not the first person to ask this, I have written up a complete list for these tools and have sent it off ...
- I need the Accessories Kit 877116.
Hello:
The Accessories kit 877116 is no longer available, but we could supply all the parts that were in the kit. However, you don't get ...
- I need a crankshaft for the 3.0 GS/SX GLP-C 3858953
Hello:
The crankshaft for the 3.0 GS/SX GLP-C 3858953 is obsolete from Volvo Penta and I was unable to find anyone who had one.
However, I could ...
- Is there a conversion to make the OMC Cobra outdrive a Counter-rotating prop outdrive(such as Volvo's Duo Prop)? If so, what would the cost associated be?
Hello:
Your 1995 OMC Cobra was really manufactured by Volvo Penta for OMC and was called an SX-C (single prop) or a DP-S (dual prop).
So any ...
- I can't find a RA119005 potentiometer. Can you help?
Hello
Your original RA119005 potentiometer on your PCM engine, has been
replaced by the RA119005A which then in turn was replaced by R119005A.
To use this new R119005A ...
- I have a 19 foot bay boat with a Suzuki df140 and a stainless 3 blade 14x22 prop. My rpms wide open are pushing 6500, however Suzuki recommends 5600-6200. What prop change would you recommend?
You have two options.
1) You could try switching over to a 4 blade 14"x21 4 blade SS prop (which we could ...
- I ordered both a cable connection (part # 22769770) Volvo Penta HS45AE-C transmission but it is not compatible with the solenoid, yet Volvo and ZF is showing that is the correct part number. How do I find the correct connection or harness?
What has happened is that Volvo Penta (and ZF Marine) have changed the solenoids
from 874097 (ZF #3312 308 064) to 22774568 (ZF#3312 308 183). ...
- I have a Volvo Penta 2000 marine engine, three cylinder. Is it OK to use synthetic engine oil, 10/40w?
Originally, back in the day, the 2000 series used straight 30 weight which is what I would
probably use. Volvo Penta no longer supplies a 30 ...
- I am looking for a gear set, part number 3858461.
This lower gear set is in a DPX-A or DPX-R which were drives that only lasted a couple
of years. These drives were discontinued years ago ...
- I would like to know where & how the Sending Temperature Alarm for my Velvet Drive 5000 Model No. 20-01-004, ratio 2.040: Serial NO. 6410 is displayed.
Crusader R020037 Switch High Temperature Alarm, 235-F. High Temp Alarm Switch, screws into top of Transmission, so it just connects to the alarm buzzer.
If you wanted to ...
- I have Volvo saildrive 110s MS25 (Serial Number 310103047) and I'm looking for the disc kit and the Seal kit, I'm not able to find the part numbers for those. I know this items are discontinued, but I'm still unable to give up. What are my alternatives?
Our records show that you have a 120 S-E sail drive. If this is correct there are no disc kits in this one as it
uses ...
- I have a 3.0 Volvo Penta engine on my 18.5 stingray. The trim cylinder is leaking fluid from a seal. I can’t seem to find a rebuild kit or seals. Can you help?
If your drive is an SX drive then I can supply a good rebuild kit that I designed and we have
been selling for years.
However, if ...
- I am after a left hand propeller for the QL 450 bow thruster. Is it possible to obtain one? Part number 41100689.
I am sorry, but props (and parts) for the QL line are just about impossible to get. QL was purchased by Side Power (who makes ...
- I need a prop for a Volvo 2003T with a drive MS2B with a 2.4 reduction, have maximum diameter available of 14".
I will need the length and weigh of the sail boat to make a recommendation.
Typically you need .10 of the diameter of the prop between ...
- I have a 2005 signature 330 chaparral boat with the composite outdrive. the piece that attatches to the boat from the outdrives are worn out. are these replacable (I think called the transom shield)
Volvo Penta no longer supports these drives and many (almost all) of the parts are no longer available. The transom shield kit
is not available.
However, I ...
- I have a V5 7GXIDP 4012032888 Chaparral 265 551 and I need to replace the volvo penta inboard 400HP engine with fuel pump. I can ship my core. Do you have this engine for sale?
These 5.7 GXI engines are no longer available from Volvo Penta. GM, who used to make the blocks, is no longer
manufacturing them. I would need ...
- I am looking for a propeller, 17" dia x 12" pitch and is right hand rotation.
I can quote this prop, but the dimensions are a little unusual.
The rule of thumb is that the shaft diameter should be no more than ...
- I have a blown piston and need the piston and rings. I had a look at the engine catalouge and have seen three different serial nos. for my pistons. As follows:
795-882692 – Piston Grade A
795-882693 – Piston Grade B
795-882694 – Piston Grade C
Can you please guide me on how I can recognise which Piston I need to order? The serial no. of my engine is 88109605.
I tried to look on the blown piston, yet the only number I have seen is as follows:
3772B (which has nothing to do with the part numbers I found in the cataloge above.
You will need the manual 90-863016001 ($105) to figure out which piston you need.
You might see if you can find the manual on the web, but ...
- I am looking to replace the Hurth transmission as it is slipping but cannot see how to identify the model number, can you help?
Perkins 4.108 usually came with the HBW 50 or HBW100 or the HBW 150. If the tag is gone can you send me a couple ...
- I am trying to determine the horsepower on my Mercruser 454 Magnum 1993, where do I look?
If you can give me the serial number I could check with Merc.
But my guess is around 320-350 HP as this is a Carb. engine. ...
- I ordered the the pipe #3589415 for the "garden hose flush project" as per your web site. The part delivered has a tiny pipe connection. Is this really sufficient to supply enough water to run my Volvo penta 5.0 gi engine on?
There are only two size of T’s the 1” and the 1.25” depending on whether you have a small block or a big block.
It supplies ...
- I am looking for accessories kit #877116, where can I find it?
The Accessories kit 877116 is NLA, but we could supply all theparts that were in the kit (see attached quote).However, you don't get the nice ...
- I just bought a 1998 chris craft 230 deck with a Volvo Penta. The only ID plate on the outdrive says 3868719 1.51 t0820479. Can you tell me what type of drive this is?
Neither the 3868719 (Volvo Penta like number) nor the T0820479 (OMC serial number) come up in
the system, which is not that surprising as OMC records ...
- Is there a conversion to make the OMC Cobra outdrive a Counter-rotating prop outdrive (such as Volvo's Duo Prop)?
Your 1995 OMC Cobra was really manufactured by Volvo Penta for OMC and was called an SX-C (single prop) or
a DP-S (dual prop).
So any SX-M ...
- I need a cyl head gasket, #3809167, can you order it for me?
It turns out that the cyl head gasket 3809167 is obsolete from Volvo Penta.However, the 876431 complete gasket kit (including head gasket 3809167) isstill available. ...
- I need a gimbal ring #3856987 but cannot find it. What do I do?
The gimbal ring 3856987 used to come with the housing (3857979) with the 1" water line.Eventually Volvo Penta stopped using the 1" water line housing ...
- I am looking for an EDC 4" Display #874293 but can't find it. Where do I look?
Volvo Penta changed the part number again (same price and same part but with a new part number and harness).So the original EDC 4" Display ...
- I am looking for two SAE#3 adapter plates to go from a Cummins 4BT engines to Borg Warner S7000 gears. Is this something you can help me with?
I am sorry, but the S7000 Borg Warner is just too old for us to get parts for.
I thought that the bolt pattern of the ...
- I ordered the prop remover tool #3855877 and have not received it yet. Is it available?
The Volvo Penta part number 3855877 tool (removes outer prop shaft housing on DPS-M) has been
back ordered for weeks and Volvo Penta is unsure when ...
- I need a circuit card for my QL BP900, but cannot find it. Schematic says the part number should be 41100658, how would I find it to order it?
The part number 41100658 has been changed to 21281780.These are still available as of today, but once they are sold out (from Volvo Penta), they ...
- I need a cylinder kit for my Volvo Penta diesel engine, #876098. Can you order it?
The cylinder kit 876098 comes with the liner, piston, piston rings and pin, and seals.However, this part number has been discontinued and is no longer ...
- I need a new spinner for my Volvo Penta IPS. The part number is 3886126, but I can't find it. Can you help?
The spinner 3886126 has been replaced by a new spinner, a new nut and a new bolt, 22072153, 22001844 and 963699 respectively.
You need to purchase all ...
- I need a seal and clutch kit for my HSW630VI 2.5.. Which one should I get?
3312199021 is from ZF Marine directly. ZF Marinepurchase the Hurth transmission company back in 1996 so the ZF 63IV is the sameas the HSW630VI.This kit ...
- I am looking for a replacement HBW10, do you have any in stock?
he HBW10 is the same as the ZF 10M. However ZF Marine no longer makes the ZF 10M and insteadhas sold the ZF10M manufacturing rights ...
- Is injector #3854518 no longer available for purchase?
The injector 3854518 is indeed obsolete. I haven't been able to find anyone thathas one of these or able to recommend a replacement.However, Mercruiser had ...
- I am looking for fuel control cell part #R089004 for my PCM engine, do you have any in stock?
According to PCM, the only solution they can offer is a complete new RA080031 plus anadditional fitting R024163 to replace the R089004.Attached is a quote ...
- I need a repair kit for my circulation pump on my volvo penta, where do I find it?
If you have the old circ pump 860358 you need to purchase the old repair kit 876270. This repairkit is NLA but I can still ...
- I need a way to fit a 1994 Volvo Penta version 7.4 manifold to a Volvo Penta 740B(A). Are there kits for this?
Here is the work around to replace the manifold and two piece riser from yourVolvo Penta 740B(A) to the 1994 Volvo Penta version 7.4 manifold ...
- Is the fresh water cooling kit #3842763 still available?
I am sorry but Volvo Penta has discontinued 3842763 the fresh water cooling kit. They no longersupply the kit.
I meticulously put together a kit for ...
- I need a head gasket kit for my Volva Penta engine. What would you suggest?
Attached is a quote for the head gasket. This head gasket is back ordered for someindeffinate time through Volvo Penta, but I do have a ...
- I need transom shield #21176076. Do you have any available?
The 21176077 in the kit that includes the 21176076 and all the parts
below it with the little dot (like the studs and the seas).
Most times ...
- I am looking for a wiring harness for a Mando alternator. Do you have any in stock?
Here is a quote for the harness you need to use with your Mando alternator.
84-861236A2 HARNESS (MANDO ALT. USED) $325.00I did find one person in ...
- Is there valve adjustments required on a IPS-600 D 435 HP
don"t know ...
- Issues with Volvo Penta 3857184 flange screw
The 3857184 bolt from Volvo Penta is still inexplicably on back order with "vendor issues" After much discussion with Volvo Penta the bolt is described ...